Flushmount Front Turn Signals

Upgrades.FlushmountFrontTurnSignals History

Hide minor edits - Show changes to markup

March 14, 2008, at 04:15 AM by CnDnMax -
Added line 46:
  • Follow the steps above, minus the fairing drilling of course.
February 18, 2008, at 02:01 AM by Cndnmax - Alternate method
Added lines 40-50:

If you dont want to drill a hole in the fairings:

  • Place the signal so the front hole is positioned on the removable tab and mark with a pencil
  • Drill the hole and cut the 2nd screw near the base of the flush mount and put some electrical tape over the end
  • Bolt in the front screw using washers on the other side of the tab

http://img20.imageshack.us/img20/8158/0927071517ir1.jpg

Finished product: http://img20.imageshack.us/img20/1977/0927071652ik9.jpg Alternate method by: CndnMax

April 05, 2007, at 05:15 PM by Turd Ferguson - Added safety disclaimer
Changed lines 3-5 from:

This mod is specifically for the GS500F models.

to:

This mod is specifically for the GS500F models. It should, however, be noted that by performing this modification turn signal visibility will be significantly affected.

August 22, 2006, at 06:46 PM by Niccolai -
Added line 22:
Added line 24:
Added line 26:
Added line 28:
Added line 30:
August 22, 2006, at 06:45 PM by Niccolai -
Changed lines 1-3 from:

boldHow to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

to:

How to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

August 22, 2006, at 06:44 PM by Niccolai -
Changed lines 1-2 from:

<b>How to Replace Front Marker Lights With LP USA Flush Mount Marker Lights </b>

to:

boldHow to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

August 22, 2006, at 06:44 PM by Niccolai -
Changed lines 1-2 from:

bigHow to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

to:

<b>How to Replace Front Marker Lights With LP USA Flush Mount Marker Lights </b>

August 22, 2006, at 06:43 PM by Niccolai -
Changed lines 1-2 from:

How to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

to:

bigHow to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

August 22, 2006, at 06:41 PM by Niccolai -
Changed lines 31-34 from:

<img src=http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_4.jpg>

to:

http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_4.jpg

Credit: Todd Yugo

August 22, 2006, at 06:40 PM by Niccolai - Credit: Todd Yugo
Changed lines 12-13 from:

<img src="http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_1.jpg">

to:

http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_1.jpg

Changed lines 16-18 from:

<img src="http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_2.jpghttp://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_3.jpg">

to:

http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_2.jpg

http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_3.jpg

August 22, 2006, at 06:39 PM by Niccolai - Credit: Todd Yugo
Added lines 1-29:

How to Replace Front Marker Lights With LP USA Flush Mount Marker Lights

This mod is specifically for the GS500F models.

- Remove lower front farings. - Remove bolt on back side of faring holding marker light. - Remove electrical connectors from the bike harness. - Remove factory marker lights. - You will notice that the mounting location is raised.

<img src="http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_1.jpg">

-You will need to cut a part of this raised area away. This is an idea as to what you will need to cut off.

<img src="http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_2.jpghttp://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_3.jpg">

- After the extra plastic is removed you will need to take the cover off the flush mounts and put them in the area that you want to mount them. - Mark the holes that the marker lights use to mount. - Drill the holes. - Place wires through the stock hole and then bolt the new flush mount marker lights in place. - Connect new marker light to the factory harness using the recommendations for which wire goes to what wire. - Replace farings.

You should end up with something like this:

<img src=http://memimage.cardomain.net/member_images/12/web/2292000-2292999/2292813_4.jpg>